Compressive sensing theory can be applied to reconstruct the signal with far fewer measurements than what is usually considered necessary, while in many scenarios, such as spectrum detection and modulation recognition, we only expect to acquire useful characteristics rather than the original signals, where selecting the feature with sparsity becomes the main challenge. With the aim of digital modulation recognition, the paper mainly constructs two features which can be recovered directly from compressive samples. The two features are the spectrum of received data and its nonlinear transformation and the compositional feature of multiple high-order moments of the received data; both of them have desired sparsity required for reconstruction from subsamples. Recognition of multiple frequency shift keying, multiple phase shift keying, and multiple quadrature amplitude modulation are considered in our paper and implemented in a unified procedure. Simulation shows that the two identification features can work effectively in the digital modulation recognition, even at a relatively low signal-to-noise ratio.

HDMI Encoder Modulator, 16in1 Digital Headend, HD RF Modulator at Soukacatv.com



SKD32 IPTV Gateway


SKD3013 3 Channel HD Encode Modulator


SKD81 IP Set Top Box


1. Introduction

Constantly increasing volume of data transmitted through the mobile communication networks and the needs of users to increase the data rates lead to rapid development of mobile communication systems. The future fifth generation (5G) wireless communication tends to achieve a remarkable breakthrough both in data rate and spectral efficiency [1]. With demand for large data size and high data rate, vast spectrum resources are required urgently. However, most spectrum resources below 2G are fixedly occupied by other industries, although they have not been fully utilized. Considering this, the purpose of spectrum sensing in mobile communication networks is to share spectrum resources with other industries, without interfering with their normal operations. Moreover, spectrum sensing can be also applied to coordinate the public resources, which is a revolutionary change of the fixed spectrum allocation system [2].

On account of the rearrangement function needed in spectrum sensing and the fact that modulation recognition can provide reliable parameters for it, digital modulation recognition is of great importance in the whole system [3]. The goal of digital modulation recognition is to identify the modulation format of an unknown digital communication signal. For modulation classification, two general classes of classical methods exist: likelihood-based and feature-based methods, respectively [4, 5]. Based on the likelihood function of the received digital signal, the former method makes the decision by comparing the likelihood ratio with a threshold. In the feature-based method, several features are usually chosen and the decision is made jointly.

However, in traditional sensing process, two approaches are based on Shannon-Nyquist sampling theorem and the data scale to deal with can be enormous with a quite wide band especially in the cooperation networks. These years, researchers have brought compressive sensing (CS) in, which can solve the problem of high sampling rate caused by Shannon-Nyquist sampling theorem. It is declared that if the signal has a sparse representation in a fixed basis, we can reconstruct the sparse domain of the signal by solving an optimization algorithm, using samplings far fewer than dimensions of the original signal, and the original signal can be obtained by a simple matrix operation [6, 7].

In many CS conditions, we expect to acquire some signal characteristics rather than recovering the original signal, since reconstructing signals allows for lots of extra operations, which results in higher complexity in both time and space. Researchers have already carried out much related valuable work in reconstructing signal characteristics based on CS [8, 9]. Inspired by these researches, we are devoted for finding identification features which can be used in the digital modulation recognition and simultaneously have sparsity, meaning they can be reconstructed directly by compressive samples.

In this paper, we propose a feature-based method based on CS for digital modulation recognition. We construct two identification features and use compressive samples to recover them directly, without recovering the original signals. One identification feature is the spectrum of received data and its nonlinear transformation, which is based on the feature proposed by [10], and the other is a compositional feature of multiple high-order moments of the received data. These two features can be used to identify various kinds of modulation modes, and, in this paper, we only focus on multiple frequency shift keying (MFSK), multiple phase shift keying (MPSK), and multiple quadrature amplitude modulation (MQAM). Simulations would be carried out to indicate that the performance of our method can be effective and reliable, with lower complexity and better antinoise property than traditional ones [11, 12].

The rest of this paper is organized as follows. Section 2 would present the system model adopted throughout the work, both the signal model and compressive sensing model. In Section 3, we construct two identification features and analysis sparsity of them. In Section 4, we build the linear relationships between identification features and compressive samples and give a brief introduction of the recovery method. Then, the whole recognition flowchart will be shown in Section 5. Simulations and analysis are present in Section 6. And, finally, we draw the conclusion in Section 7.

2. System Model

2.1. Signal Model

In a spectrum sensing scenario, we assume that a wide band received signal has one of the following modulation modes: where represents the amplitude of the received signal, represents the symbol period, represents the impulse response of pulse shaping low-pass filter, in which we choose rectangular pulse in this paper, and stands for additive Gaussian white noise (AWGN). In the whole process, the timing offset and the carrier offset are both assumed to be zero, and the form of is chosen as follows: where and , respectively, stand for the carrier frequency and order of the chosen modulation mode, is the carrier spacing, and are a set of discrete levels. It is worth noting that there is no need of pulse shaping for MFSK, while in order to unity the form as (1), we regard in MFSK as 1, which would not influence the use of it.

2.2. Compressive Sampling Model

According to the theory of CS, the compressive sampling process can be modeled analytically as where is the -length sampling vector of the received signal at a rate no lower than Nyquist sampling rate. Represents the subsampling measurements. is a real-value measurement matrix of size , which complies with the restricted isometry property (RIP), such as Gaussian matrix, partial Fourier transform matrix, or others. In order to reconstruct the th power of signal in Section 4.1, we adopt a special measurement matrix, with the value of “1” randomly located in each row and other elements being zero. Owing to the randomization of row elements, the matrix satisfies the RIP requirement as well as Gaussian matrix. Furthermore, the two-valued property of the matrix can enormously simplify the matrix operations, which make it possible to establish linear relationship between the nonlinear reconstruction targets with the compressive samples.

To classify the modulated signal based on, we will firstly build the linear relationships between and the identification features and then reconstruct the features directly with compressive samples by solving an optimization algorithm, which would then be used to do digital modulation recognition.




SKD121X Encoding & Multiplexing Modulator


Household Universal Encoding & Modulation Modulator



SKD19 Series 1U Rack 12CH Encode Modulator

3. Construction of the Identification Features

To achieve the goal of classifying modulation types accurately, identification features should be chosen with distinguishing details for each modulation type firstly. Secondly, identification features should have desired sparsity, in order to be constructed by compressive samples based on the theory of CS. According to these two requirements, we propose and construct the following two identification features.

3.1. Feature 1: Spectrum of the Signal’s th Power Nonlinear Transformation

Referring to [9], we calculate the th power of the received signal; that is, where (). In the following, it will be shown that the spectrum of specific power order of signal level presents the recognizable characters for certain modulation types and orders. is the noise caused by nonlinear transformation of .

Then, we calculate the spectrum of, which is represented as, with ranging from 0 to a larger number. We have the following relationship: where represents the -point IFFT matrix.

For different kinds of modulation modes, the results are quite different, which can be used to do the recognition, and we call this feature the spectrum feature below.

For MFSK, according to (1) and (2), the spectrum of it can be calculated as follows: where stands for the impulse function. Obviously, there is impulse in the spectrum of MFSK, and the number of these impulses just corresponds to order. As a contrast, the spectrum for MPSK can be presented as follows: where stands for the convolution operation. The spectrum of MPSK comes out to be a monotone decreasing sine function, with no impulse. The calculation process of spectrum of MQAM is similar to MPSK, and their consequences are also similar. Figure 1 shows the results of different modulation types by. From (a) and (b), we can see that there is apparent impulse for MFSK, just as we analyze in theory, quite different from that in (c) and (d), which represent the results of MPSK and MQAM, respectively. That is to say, we can distinguish MFSK from others by the spectrum of the signal, and the number of pulses indicates the order of MFSK.

Figure 1: Spectrum of different modulation modes.

For MPSK, when, from the expression, we can see that there is no impulse in this condition. However, when, for, we choose rectangle filter. Since, becomes a constant, and the Fourier transform of it is an impulse. Based on it, we compare the results of, and, referring to Figure 2. It can be seen that the impulse firstly appears when, with varying from small to big, which can be used to determine the order of MPSK.

Figure 2: Spectrum of the power of signal modulated by MPSK.

As for MQAM, owing to similarity of the signal constellation, the property of MQAM is similar with QPSK, shown as Figure 3. It can be easily seen that the impulse firstly appears when, and it has no relationship with the specific order of it.

Figure 3: Spectrum of the power of signal modulated by MQAM.

The sparsity of this feature is in inverse proportion with, which represents length of the signal as well as the IFFT size, on condition that there appears the impulse.

To sum up, the only remaining problem is to distinguish QPSK and MQAM. Therefore, we construct another feature for it.

3.2. Feature 2: A Composition of Multiple High-Order Moments of the Signal

For a digital modulated communication signal, the mixed moments of order are defined as (6), at a zero delay vector [10]: where the superscript denotes conjugation and means calculating the mean value.

In our system model, we intend to acquire and as recognition parameters, which we call the high-order moment feature.

With carrier known, symbols in the digital signals can be regarded as points in the signal constellation [13, 14]. Since points in digital signals of linear modulations are of equal probabilities, when the data size is large enough, we can use points in the signal constellation to calculate the theoretical values of and, as Table 1 shows.

Table 1: Theoretical values of and.

Referring to Table 1, of different modulation formats are of different theoretical times compared to, which is the square value of.

We define the identification characteristic in

We take QPSK and 16QAM as examples. According to (11), the theoretical values of QPSK and 16QAM, respectively, come out to be 1 and 0.68. If we get the identification characteristic of a signal, we can then identify the modulation format by comparing with a suitable decision threshold.

Since high-order moment is a kind of statistics, we need sample several times. Then, to obtain and, we construct matrixes as follows: where represents conjugate transpose, represents transpose, and stacks all columns of a matrix into a vector. For, the element of matrix at row, column, is, are elements in the signal. When, meaning diagonal elements, the values are equal to based on the definition of high-order moments. However, when, the value comes out to be zero for the un-correlation between symbols of the signal. For, corresponds to the element of. When, the relationship is that corresponds to the element of. According to (10), is the desired value, so the diagonal elements of are equal to. Other elements are zero for the un-correlation between symbols of the signal. The theoretical figures of and are shown as Figure 4.

Figure 4: and of the signal modulated by 16QAM.

It is obvious that and in Figure 4 are sparse. For, all diagonal elements are nonzero, meaning the sparsity degree of it is. For, the elements of are nonzero, meaning the sparsity degree of it is.

4. Recovery of the Identification Features with Compressing Samples

In this section, we introduce the approaches of recovering the two identification features based on CS. We firstly build the linear relationships between compressive samples and the defined features and then give a brief introduction of the reconstruction algorithm and the practical selection strategy for the measurement matrix.

4.1. Linear Relationships between Compressive Samples and the Identification Features

4.1.1. Linear Relationships between Compressive Samples and the Spectrum Feature

It is obviously that the power of the signal is a nonlinear transformation. To get linear relationship between compressive samples and the spectrum of the signal’s power nonlinear transformation, we choose the special measurement matrix proposed in Section 2. According to the nature of this certain-form matrix, we can easily get the following relationship based on (3): and is the measurement matrix for feature 1. Then, referring to (5), we obtain where the sensing matrix we needed is.

4.1.2. Linear Relationships between Compressive Samples and the High-Order Moment Feature

For this identification feature, the sampling matrix can be chosen as any one as long as it satisfies the restricted isometry property (RIP):(i): according to (3) and the nature of transpose, we get the following relationship, and stands for the measurement matrix for : Take the average of both sides: We use to represent , simultaneously refer to (12), and then get Next, we apply the property to transform (19) to (20). It is worth noticing that, for is a real-value matrix: where can be regarded as the sensing matrix, with the scale of. (ii): since the sparsity degree of is far fewer than that of, the dimension of signal needed and scale of measurement can also be very low. We represent the measurement for as, while the only difference of it from is the dimension. Similar to (17), there is Then, according to, we can transform the two-dimensional relationship into one-dimensional relationship: We can obtain Take the average of both sides: Based on (13), we get the relationship: where denotes. And then we have where the sensing matrix is.

4.2. Reconstruction of Identification Features

Zy, Rz21, and Rz40 can be calculated by the sampling value. With sensing matrixes and measurement vectors known, the reconstruction of the sparse vectors can be regarded as the signal recovery problem by solving the NP-hard puzzle as follows, taking as an example: This can be transformed into a linear programming problem: which is called -norm least square programming problem and is proved to be convex that there exists a unique optimum solution. I > o is a weighting scalar that balances the sparsity of the solution induced by the -norm term and the data reconstruction error reflected by the -norm LS term.

In Section 4.1, we have mentioned recovering three recognition features by using measurement matrixes, and, respectively. However, practically, only using as the compressive measurement may meet the requirement of recovering all of the features. The reasons are that and differ in the dimension but are both designed with the constraint of RIP property only. From the other aspect, the primary requirement of constructing matrix is also the RIP condition.

5. Modulation Recognition with the Identification Features

Given a received communication signal modulated by MFSK, MPSK, or MQAM, we firstly get compressive samples using measurement matrixes present in Section 2. In this process, due to difference of sparsity we have analyzed in Section 3, various features may apply various length of the signal, and this can be decided based on actual situations. According to the approaches proposed above, the identification features can be easily obtained. Then, we can recognize the modulation format effectively referring to the flowchart shown in Figure 5, and specific steps are listed in the following.

Figure 5: The process of digital modulation recognition.

Step1. Reconstruct the spectrum feature when with compressive samples. If there is impulse in the recovered spectrum, the modulation mode can be identified as MFSK, and the number of impulses indicates the order of it. However, if there is no impulse in the feature, the communication signal is modulated by MPSK or MQAM, and then Step 2 should be conducted.

Step2. Reconstruct the spectrum feature when with compressive samples and observe value of when the impulse firstly appears. If when the impulse appears, the modulation mode can be regarded as QPSK or MQAM, and then we go to Step 3. However, if when the impulse appears, the signal is modulated by MPSK and this value of is the order of it.

Step3. Reconstruct and of the signal with compressive samples, get average values of the diagonal as and, respectively, and then calculate based on (11). Compare with the calculated boundary values shown in Table 1 and determine the modulation type.

6. Numerical Results

This section presents the simulation results of our feature-based recognition method. We firstly generate a stream of signals modulated by MPSK, MFSK, or MQAM. All the signals share the same bit rate kbit/s and the carrier frequency kHz, and the carrier spacing for MFSK is kHz. For the two proposed features, the observation time is various because data volumes needed by the two features are all different. The performance of reconstruction is closely related to the signal-to-noise ratio (SNR), which is set as a variable in our simulation, and simulations at every SNR are carried out for 500 times.

As mentioned above, information we need to capture in feature 1 is whether there are impulses and the number of them, rather than accurate numerical values. Therefore, we apply correct detection rate of pulse to evaluate the performance of reconstruction of spectrum feature, which is shown in Figure 6. We set a decision threshold which equals two-thirds of the biggest reconstructed value, and if there is no other value larger than the threshold, the biggest value would be regarded as the impulse. In this scenario, the compressive ratio is set as 0.3, which means. We calculate the detection rate for MFSK signal on, BPSK on, QPSK and MQAM on, and 8PSK on, respectively. It is obvious that the detection rate varies a lot with. The reason is that the power of signal is a nonlinear transform, meaning that the uniformly distributed noise is magnified, and the degree of magnification extends as the increasing of . Therefore, detection rate of impulse when is the worst one.

Figure 6: Correct detection rate of impulse in reconstructed feature 1.

Figure 7 shows the mean square error (MSE) of reconstructed feature 2 with respect to the theoretical ones. That is,

Figure 7: MSE of reconstructed and with different compressive ratio.

We give the MSE of reconstructed and, respectively, with the compressive ratio chosen as 0.3 and 0.45. From Figure 7, we can see that the performance of reconstruction of is closely related to the compressive ratio, while the performance of reconstruction of is relatively perfect even at a low compressive ratio. Moreover, we can easily get the conclusion that when the compressive ratio is suitable, the precision of feature 2 is high enough as long as the SNR is higher than 10 dB.

Figure 8 shows the correct classification rate of different modulation modes at relatively low SNR. Difference of the correct classification comes from various performance of reconstruction of features, which has been shown in Figures 6 and 7. MFSK has high recognition rate, larger than even when SNR = −6 dB. For MPSK, the correct recognition rate declines as increases. However, for QPSK and MQAM, the performance is quite different, and we give the following analysis.

Figure 8: Correct classification rate of different modulation modes.

According to [14], we have the fact that of just the signal and mixture of noise and signal are of the same value, so the main cause of the error comes from.

As for, we have the following proof stating the variation of the value in noisy condition and noiseless condition. To describe this clearly, M2,1(y0), M2,1(v) , and M2,1(y) are, respectively, used to replace while being in the following condition of signal only, noise only, and the mixture of noise and signal:

is zero-mean random measure noises with Gaussian distribution, which is independent from . According to the nature of expectation, we know that

Therefore, we can obtain the following relationship: meaning is the sum of signal power and noise power.

From (11) and (27), we can obtain the relationship of the theoretical and the actual: where denotes noise power and denotes signal power.

To sum up, is added by the power of noise, and, as a consequence, the identification parameter becomes smaller; thus, QPSK may be recognized as 16QAM. Therefore, the correct recognition rate of 16QAM is much higher than QPSK when SNR is lower than 10 dB, as shown in Figure 8.

7. Conclusion

To solve the problem of high sampling rate for digital modulation recognition in spectrum sensing, we have proposed a feature-based method to identify the modulation formats of digital modulated communication signals using compressive samples and have greatly lowered the sampling rate based on CS. Two features are constructed in our method, one of which is the spectrum of signal’s the power nonlinear transformation, and the other is a composition of multiple high-order moments of the signal, both with desired sparsity. By these two features, we have applied suitable measurement matrixes and built linear relationships referring to them. The method successfully avoids reconstructing original signals and uses recognition features to classify signals directly, declining the algorithm complexity effectively. Simulations show that correct recognition rates are different for different modulation types but are all relatively ideal even in noisy scenarios. In actual situations, the method can be decomposed aiming at variable demands, and, for further work, we tend to improve the performance of the whole method continuously, especially the noise elimination in the classification of QPSK and MQAM.



Established in 2000, the Soukacatv.com main products are modulators both in analog and digital ones, amplifier and combiner. We are the very first one in manufacturing the headend system in China. Our 16 in 1 and 24 in 1 now are the most popular products all over the world.

For more, please access to https://www.soukacatv.com.



CONTACT US

Company: Dingshengwei Electronics Co., Ltd

Address: Bldg A, the first industry park of Guanlong, Xili Town, Nanshan, Shenzhen, Guangdong, China

Tel: +86 0755 26909863

Fax: +86 0755 26984949

Mobile: 13410066011

Email: [email protected]



Source: https://www.hindawi.com/journals/misy/2016/9754162/