Differential pulse code modulation is a technique of analog to digital signal conversion. The SOUKA modulators can achieve the upgrade of Analog to Digital smoothly. This technique samples the analog signal and then quantizes the difference between the sampled value and its predicted value, then encodes the signal to form a digital value. Before going to discuss differential pulse code modulation, we have to know the demerits of PCM (Pulse Code Modulation). The samples of a signal are highly correlated with each other. The signal’s value from the present sample to next sample does not differ by a large amount. The adjacent samples of the signal carry the same information with a small difference. When these samples are encoded by the standard PCM system, the resulting encoded signal contains some redundant information bits. The below figure illustrates this.

HDMI Encoder Modulator, 16in1 Digital Headend, HD RF Modulator at Soukacatv.com

Analog modulator+Total

Redundant Information Bits in PCM

The above figure shows a continuing time signal x(t) denoted by a dotted line. This signal is sampled by flat top sampling at intervals Ts, 2Ts, 3Ts…nTs. The sampling frequency is selected to be higher than the Nyquist rate. These samples are encoded by using 3-bit (7 levels) PCM. The samples which are quantized to nearest digital level as shown by small circles in the above figure. The encoded binary value of each sample is written on the top of the samples. Just observe the above figure at samples taken at 4Ts, 5Ts, and 6Ts are encoded to the same value of (110). This information can be carried only by one sample value. But three samples are carrying the same information means redundant.

Now let consider the samples at 9Ts and 10Ts, the difference between these samples only due to the last bit and first two bits are redundant since they do not change. So in order to make the process this redundant information and to have a better output. It is an intelligent decision to take a predicted sampled value, assumed from its previous output and summarize them with the quantized values. Such a process is called as Differential PCM (DPCM) technique.

Principle of Differential Pulse Code Modulation

If the redundancy is reduced, then the overall bitrate will decrease and the number of bits required to transmit one sample will also reduce. This type of digital pulse modulation technique is called differential pulse code modulation. The DPCM works on the principle of prediction. The value of the present sample is predicted from the previous samples. The prediction may not be exact, but it is very close to the actual sample value.

Differential Pulse Code Modulation Transmitter

The below figure shows the DPCM transmitter. The transmitter consists of a comparator, quantizer, prediction filter and an encoder.

Differential Pulse Code Modulator

The sampled signal is denoted by x(nTs) and the predicted signal is indicated by x^(nTs). The comparator finds out the difference between the actual sample value x(nTs) and the predicted value x^(nTs). This is called signal error and it is denoted as e(nTs)

e(nTs)= x(nTs)- x^( nTs) …….(1)

Here the predicted value x^(nTs) is produced by using a prediction filter(signal processing filter). The quantizer output signal eq(nTs) and the previous prediction is added and given as input to the prediction filter, this signal is denoted by xq(nTs). This makes the prediction closer to the actually sampled signal. The quantized error signal eq(nTs) is very small and can be encoded by using a small number of bits. Thus the number of bits per sample is reduced in DPCM.

The quantizer output would be written as,

eq(nTs)= e(nTs)+ q(nTs) ……(2)

Here q(nTs) is quantization error. From the above block diagram the prediction filter input xq(nTs) is obtained by sum of x^(nTs) and the quantizer output eq(nTs).

i.e, xq(nTs) = x^(nTs)+ eq(nTs).………. (3)

by substituting the value of eq(nTs) from the equation (2) in equation (3) we get,
xq(nTs) = x^(nTs)+ e(nTs)+ q(nTs)……. (4)

Equation (1) can written as,

e(nTs)+ x^( nTs) = x(nTs)……. (5)

from the above equations 4 and 5 we get,

xq(nTs) = x(nTs)+ x(nTs)

Therefore, the quantized version of signal xq(nTs) is the sum of original sample value and quantized error q(nTs). The quantized error can be positive or negative. So the output of the prediction filter does not depend on its characteristics.

Digital modulator NEW + Total(1)

Differential Pulse Code Modulation Receiver

In order to reconstruct the received digital signal, the DPCM receiver (shown in below figure) consists of a decoder and prediction filter. In the absenteeism of noise, the encoded receiver input will be the same as the encoded transmitter output.

Differential Pulse Code Modulation Receiver

As we discussed above, the predictor undertakes a value, based on the previous outputs. The input given to the decoder is processed and that output is summed up with the output of the predictor, to obtain a better output. That means here first of all the decoder will reconstruct the quantized form of original signal. Therefore the signal at the receiver differs from the actual signal by quantization error q(nTs), which is introduced permanently in the reconstructed signal.

S. NO


Parameters


Pulse Code Modulation (PCM)


Differential Pulse Code Modulation (DPCM)

1


Number of bits


It uses 4, 8, or 16 bits per sample


PCM bits

2


Levels, step size


Fixed step size. Cannot varied


A fixed number of levels are used.

3


Bit redundancy


Present


Can permanently remove

4


Quantization error and distortion


Depends on the number of levels used


Slope overload distortion and quantization noise are present, but very less as compared to PCM

5


Bandwidth of transmission channel


Higher bandwidth has been required since number of bits are absent


Lower than PCM bandwidth

6


Feedback


No feedback in Tx and Rx


Feedback exists

7


Complexity of notation


Complex


Simple

8


Signal to noise ratio (SNR)


Good


Fair

Applications of DPCM

The DPCM technique mainly used Speech, image and audio signal compression. The DPCM conducted on signals with the correlation between successive samples leads to good compression ratios. In images, there is a correlation between the neighboring pixels, in video signals, the correlation is between the same pixels in consecutive frames and inside frames (which is same as correlation inside the image).

This method is suitable for real Time applications. To understand the efficiency of this method of medical compression and real-time application of medical imaging such as telemedicine and online diagnosis. Therefore, it can be efficient for lossless compression and implementation for lossless or near-lossless medical image compression.

This is all about Differential Pulse Code Modulation working. We consider that the information given in this article is helpful for you to a better understanding of this concept. Furthermore, any queries regarding this article or any help in implementing electrical and electronics projects, you can approach us by commenting in the comment section below. Here is a question for you, what is the role of the predictor in DPCM technique?

Established in 2000, the Soukacatv.com main products are modulators both in analog and digital ones, amplifier and combiner. We are the very first one in manufacturing the headend system in China. Our 16 in 1 and 24 in 1 now are the most popular products all over the world.

For more, please access to https://www.soukacatv.com.

CONTACT US

Dingshengwei Electronics Co., Ltd

Company Address: Building A, the first industry park of Guanlong, Xili Town, Nanshan, Shenzhen, Guangdong, China

Tel : +86 0755 26909863

Fax : +86 0755 26984949

Phone: +86 13410066011

Email:[email protected]

Skype: soukaken

Source: elprocus

Digital modulator + Total

soukacatv others