Outdoor travel, summer night camping seems to have become the most desirable tranquility in the city! And there are some hidden dangers under these tranquility. A high power LED flashlight is particularly important. While illuminating the road forward , Can also escort your outdoor trip. https://www.olightstore.com/flashlights.html

Glare flashlight is no stranger to every outdoor enthusiast. However, if the flashlight is improperly maintained, it will cause failures such as long flashlight, fire failure, ineffective switch, running electricity, and coating falling off. But how to make better maintenance of outdoor flashlights? I believe some friends still want to know very much. The following olight will give you an analysis of some important maintenance methods and precautions, I believe it will be helpful to you.

How to use high power LED flashlight
1, Unscrew the tail cover for battery installation. Pay attention to the positive and negative terminals of the battery. Insert the battery and screw the tail cover.

2, When the flashlight is turned off, press the rubber cap in the middle to turn it on. Repeat the above steps to turn it off.

3, the light is pressed to the strongest light when the button is used for spot fire. Need to switch the light as long as you tap the switch to achieve tactical firing. The functions are, in order, extremely bright, highlight, medium bright, low bright, SOS, flash. Press the switch again to turn off the light.

4, How to charge high power LED flashlight

① Unscrew the tail cover of the flashlight and remove the battery.

② Put the battery in the special charging box (Note: When inserting the battery, the battery’s positive and negative poles must be opposite to the positive and negative poles of the battery box, otherwise it will not be charged; Eagle Eye King Raptor series tactical flashlight T-MQ-16 is specially equipped with 18650 batteries Supports Mirco USB charging)

③Remove the charger, insert two pins into the power take-in interface, and insert the jack end into the battery box jack. When charging, the light on the charger is red. When the indicator light changes from red to green, it indicates that charging is complete. At this time, you can remove the battery and use it.

Safety precautions when using high-power LED flashlights
1, Do not direct light into people’s eyes, strong light will cause permanent damage to the eyes;

2, When installing the battery, distinguish the positive and negative terminals of the battery. Otherwise, it may cause unexpected damage to the lamp beads of the flashlight;

3, It is strictly forbidden to disassemble the lamp cap to avoid damage to the reflector or bulb;

4, the battery should be charged in time when the power is low. When the flashlight is turned on in the strong light mode, if the brightness is significantly reduced, it means that the battery needs to be charged to avoid damage to the battery due to over-discharge.

5, Do not overcharge the battery for a long time. However, after the charging is completed, the charging lamp no longer blinks, indicating that the battery is fully charged. Remove the battery from the charger immediately and store it in a cool, dry place.

6, Do not use over voltage, the voltage should not exceed 4.5V, the positive side of the battery should not be placed upside down, otherwise it will burn the circuit board.

7, When the LED flashlight is not used for a long time, the battery should be taken out of the warehouse and stored in a cool, dry place.

Special attention should be paid to high-power LED flashlights:
Strong light flashlight is an object that is easy to generate heat and generate high temperature. When outdoor camping or traveling, pay attention to control the temperature change of the flashlight. After the flashlight is turned on for a long time, do not touch the glass with your hand to avoid burns. Direct contact with flammable materials with low ignition points (such as cotton cloth, haystacks, etc.) must be avoided to avoid hidden dangers such as fire due to high temperature.

High-power LED flashlight attention
Suppose that your high-power LED flashlight is used improperly and maintained, there will be failures such as long flashlight, fire failure, ineffective switch, running power, and coating falling off. The following are precautions and methods for the use and maintenance of flashlights:

1, Wipe dry with a soft cloth immediately after using the flashlight to prevent the use of rain or snow or the infiltration of moisture and hand sweat. Otherwise, the coating of the flashlight will easily fall off or rust.

2, usually do not put the flashlight on the hot stub or near the stove, but also avoid fumigation of soot, otherwise the flashlight is prone to runaway.

3, the bottom cover is opposite to the photocell. When it is extinguished, loosen or remove the battery to prevent the bottom cover from breaking through the bottom of the battery and flowing out of the slurry.

4, If the silver-plating of the back-lighting bowl is contaminated, which affects the reflection of light, it can be wiped off with clean cotton.

5, when the flashlight is installed with the battery, it must be installed with the paper sleeve, otherwise it is the easiest to run off electricity. After using the new battery for a period of time, you can change the position to extend the life of the battery.

6, Generally, the battery stops emitting light at minus 20 degrees, so pay attention to heat preservation in cold seasons.

7, Do not expose the high-power LED flashlight in the sun when not in use, and do not flash back and forth when not in use!